Furnace humidifier hookup

furnace humidifier hookup

Can I connect my humidifier to my furnace?

I dont recommend using the G and Gf connections. The humidifier should only run when in heating mode to be most effective. The C connection is available at the furnace in the same place the other thermostat wires are connected.

How does a flow-through humidifier work on a furnace?

A flow-through humidifier typically is mounted to the furnaces cold-air return duct and connects to the hot-air supply off the furnace through a humidifier supply takeoff duct.

Can a humidifier clog a furnace return duct?

This type of system clogs easily with well water or water high in mineral content. Drum and flow-through humidifiers typically mount to the cold air return duct near the furnace with a hose that connects to the warm air supply duct. A mist unit attaches to the wall next to the furnace, and only the wand extends into the warm air duct.

How do you wire a humidistat to a furnace?

Some humidistats mount to the cold air return near the furnace, while others mount in the living space near the thermostat. Either way, you need to wire the humidistat into the humidifier box. You also need to tap into an existing hot wire to power the humidifier and its transformer. Working with electricity can be dangerous.

How do I hook up a humidifier to my furnace?

You may be able to simply connect the wire from the humidifier to the W terminal in the furnace, instead of directly to the transformer. That way, the humidifier will only get power when the thermostat is calling for heat. However, without knowing more details about your system, its impossible to say for sure if that will work.

How do you test a humidifier on a furnace?

The HUM terminal on most furnaces is a 120VAC terminal. If you want to use the HUM terminal to control the humidifier, youre going to have to use a step down transformer, to drop that down to 24VAC. To measure the voltage on the HUM terminal: Set your volt meter to measure AC volts. Place one probe on one HUM terminal.

What voltage should a humidifier run on a furnace?

When the furnace is running in heat mode, you should measure ~120 volts about 1 second after the blower motor starts. According to the manufacturer, the HUM terminal is rated for 1 ampere at 120 volts. You may be able to simply connect the wire from the humidifier to the W terminal in the furnace, instead of directly to the transformer.

Do I need a furnace humidifier for my home?

Regularly running a humidifier can assist in: Home furnace humidifiers have been shown to improve lung health, relieve chronic running nose, dry throat, nose bleeds and reduce instances of illness. Humidifiers are also regularly recommended by asthma and allergy doctors.

How do you wire a humidifier to a thermostat?

If you wire it this way: Set the humidistat to ON when the home is occupied; Set the humidistat to 55-60% when away; Set the thermostat to 75-80° when away; This way, the system will only run when the humidity is above the humidity setpoint and the temperature is above the temperature setpoint.

How to wire a Honeywell humidistat?

How to Wire a Honeywell Humidistat 1 Turn off the humidifiers power source. If the humidifier plugs into a receptacle, then unplug the humidifier. 2 Strip 1/2 inch of the insulation from both wire strands in both low-voltage wire sets with wire strippers. 3 Grab one humidistat lead and one black-colored low-voltage wire strand. ... More items...

Can I connect my humidifier to my furnace?

I dont recommend using the G and Gf connections. The humidifier should only run when in heating mode to be most effective. The C connection is available at the furnace in the same place the other thermostat wires are connected.

How do you wire a humidistat to a roof?

Take two pairs of the low voltage wire sets and extend into the base just 6 inches. Each of the wires will feature a white and black colored wire strand. Grab one low voltage wire strand and one humidistat lead and twist them together using pliers. You can screw a nut over these sets of wires.

Related posts: