Hook up amp and sub

hook up amp and sub

How do I connect a preamp to a subs AMP?

The simplest way is run the pre out into a splitter, then to the main power amp and the subs amp. Most likely O.K. I would check the input impedance for the amp and the Sub, as they get paralleled with a simple splitter (Y-cable), unless the splitter has resistors to isolate the two sets of inputs.

How do you wire an amp to a subwoofer?

If you want to wire an amp to a sub and head unit, start by turning your vehicle off and popping the hood. Next, disconnect the negative terminal on your vehicle’s battery and connect a power cable to the positive terminal of the battery.

Can I use a 2-channel amp for subs?

This is a great place to use a 2-channel amp. When you wire the subs as shown in the diagram below, the total impedance will be four ohms. A bridged 2-channel amp can provide plenty of power at a reasonable price. Get some good subs and a good amp and let it rip!

How do I hook up two subs to a mono amp?

By wiring the two subs in parallel (see the diagram) youll show a 2-ohm impedance to the amp. Mono amps are built for just this kind of situation, so youll get maximum power output from your amp investment. Check the diagram below for how to hook it up. Two 4-ohm SVC subs — a great place to use a mono amp. Wiring flexibility is the key here.

How to connect a subwoofer to an amplifier?

There are a few ways that one can expect to connect a subwoofer to an amplifier, receiver, or processor (also known as a home theater receiver). The most common method is done by connecting the subwoofer to the SUB OUT or LFE output of a receiver/amplifier. But you might also come across a subwoofer that uses stereo RCA or speaker wire connections.

How do I connect my preamp to my amp board?

The signal connection from the preamp board will be two conductors for each channel that the amp board has. Usually this will be a two conductor coaxial audio wire. Center wire is plug, the shield is minus. You can cut the RCA plugs off of any audio cables and use them. The +ve - G- -ve connections are for the power supply.

Is it bad to connect a subwoofer to a preamp?

This means that you will be using the crossover in the sub and it may or may not be bad for the sound of your main speakers. I prefer to use Y cables if the preamp doesnt have two sets of pre-outs and send one signal to the sub and the other to my main amp.

How to connect a preamp to an AV receiver?

With all of your audio devices plugged into the preamp, plug the preamp’s Output or Phono Out directly into the AV receiver’s HT Bypass or Direct In. In all likelihood, this will require a pair of RCA cables. Make sure you plug red to red and white to white to get the intended right-left separation. 4.

Can you use gain on a mono block AMP?

If the amp is a mono block then yes. There are two sets of terminals on the amp for added convenience. I use gain as a volume control. Its the Audioque 2200. Yes is mono and the second terminal isnt for a second channel only so you have more room to connect wires.

How do you hook up 3 subwoofers together?

Connecting Three or Four Subwoofers If you plan to use three or four subwoofers, the best option is to make sure all the subwoofers have either RCA or LFE line-out connections and daisy chain them together using a series of subwoofer cables.

Can I use a 2-channel amp for subs?

This is a great place to use a 2-channel amp. When you wire the subs as shown in the diagram below, the total impedance will be four ohms. A bridged 2-channel amp can provide plenty of power at a reasonable price. Get some good subs and a good amp and let it rip!

Whats the best way to power a car with two subs?

A bridged 2-channel amp can provide plenty of power at a reasonable price. Get some good subs and a good amp and let it rip! Wire two 4-ohm DVC subs this way, add a 2-channel amp, and your car will be the Temple of Boom!

Related posts: