Hook up mono amp to 2 subs

hook up mono amp to 2 subs

How to wire up two subwoofers in series?

You can wire each subs voice coils in parallel and then wire the subs together in series to get a 2 ohm load to your amplifier. You could also wire each subs voice coils in series and then wire the subs together in series again to get an 8 ohm load.

Can you use gain on a mono block AMP?

If the amp is a mono block then yes. There are two sets of terminals on the amp for added convenience. I use gain as a volume control. Its the Audioque 2200. Yes is mono and the second terminal isnt for a second channel only so you have more room to connect wires.

Why are there two terminals on this amp?

There are two sets of terminals on the amp for added convenience. I use gain as a volume control. Its the Audioque 2200. Yes is mono and the second terminal isnt for a second channel only so you have more room to connect wires.

How do you wire a speaker to an amp?

Where the picture shows the wires going to the amp, you CAN have one speaker terminal in the box and take all 4 wires to it, then wire it to the amp. Best way though is to have a terminal for each speaker, or even each coil. I assume the box already has a terminal on it?

How do you connect two subwoofers to one wire?

Connect a section of wire from the positive terminal of the terminal cup (located on the back of the subwoofer box) to the positive terminal of the first subwoofer. Connect the second wire from the negative terminal of subwoofer 1 to the positive terminal of subwoofer 2.

How do you wire a dual voice coil subwoofer in series?

Need to wire a dual voice coil subwoofer in series? First, connect the positive lead from Voice Coil 1 to the positive speaker output from your amplifier. Next, connect the negative lead from Voice Coil 1 to the positive lead on Voice Coil 2. Finally, connect the negative lead from Voice Coil 2 to the negative output of the amplifier.

Should I use series or parallel wiring for my subwoofer?

If you only have one dual voice coil subwoofer, you will either use series or parallel wiring. When using a single 2Ω dual voice coil, wiring in parallel will reduce the impedance of the driver to 1Ω.

How to add two subwoofers to a home theater system?

Here are the three ways to add two subwoofers in a home theater system: If you have a home theater receiver that only has one subwoofer preamp output (sometimes labeled Pre-Out, Sub Out, LFE, or Subwoofer Out), use an RCA Y-Adapter to send two parallel low-frequency audio signals to two separate subwoofers.

How do I wire my speakers?

1 Wire your speakers in a series if they’re less than 8 ohms. Check the back of your speakers to see how many ohms, or electrical resistance, they have. 2 Unplug your amp and speakers. Unplug your amps and speakers so no electricity is running through them. 3 Clip a speaker wire between the inner terminals. ... More items...

How to connect car speakers to an amp?

How to Connect Speakers to an Amp 1 Method 1 of 3: Hooking up Car Speakers. Install an amp in your vehicle. ... 2 Method 2 of 3: Attaching Speakers in a Series. Wire your speakers in a series if they’re less than 8 ohms. ... 3 Method 3 of 3: Using a Parallel Set-up. Opt for a parallel wiring system if your speakers are more than 8 ohms. ...

How do you connect an amplifier to a receiver?

Connecting Receivers or Amplifiers . Wires must be connected correctly on both the receiver or amplifier and speakers. The positive speaker terminal (red) on the receiver or amplifier must be connected to the positive terminal on the speakers, and the same applies to the negative terminals on all the equipment.

Can you wire speakers to an amp at home?

Wiring your speakers and amp can be a huge undertaking, especially if you don’t have a lot of electrical experience. While it’s always best to leave complex projects to the pros, there are few ways you can connect your speakers to an amp from the comfort of your own home.

Related posts: